MS Square Bar Weight Calculator: Calculate Steel Weight Easily

Steel is bought and sold by weight, so knowing the weight of your MS square bar before you order is the difference between a smooth project and an expensive surprise. Order too little and work stops. Order too much and money sits idle in your yard.

MS Square Bar Weight Calculator: Calculate Steel Weight Easily

The good news is that you do not need special software. This guide works as a simple MS square bar weight calculator: one formula, a ready chart for RealEdge sizes and worked examples you can copy for your own orders.

What Is an MS Square Bar?

MS square bar, also called mild steel square bar or MS square section, is a long steel bar with a square cross section. Both sides are equal, and the size is given as a single number in millimeters. For example, a 12 mm MS square has sides of 12 mm x 12 mm.

Fabricators use MS square bar for the vertical bars of gates and window grills, railings, fencing and general fabrication, where equal strength on all sides is needed.

The MS Square Bar Weight Formula

The formula is simple and works for every size:

Weight Formula

Weight (kg per meter) = 0.00785 x Side (mm) x Side (mm)

Where:

  • Side is the length of one side of the square in mm
  • 0.00785 comes from the density of mild steel, about 7850 kg per cubic meter

To get the total weight of a bar, multiply the weight per meter by its length:

Total Weight

Total weight (kg) = Weight per meter x Length (m)

Worked Examples

Example 1: 12 mm MS square, 6 meter length

Weight per meter = 0.00785 x 12 x 12 = 1.13 kg/m

Weight of one 6 meter bar = 1.13 x 6 = 6.78 kg

Example 2: 16 mm MS square, 6 meter length

Weight per meter = 0.00785 x 16 x 16 = 2.01 kg/m

Weight of one 6 meter bar = 2.01 x 6 = 12.06 kg

Example 3: Total weight for an order of 100 bars of 12 mm square, each 6 meters

Total weight = 100 x 6.78 = 678 kg

Example 4: A bar length given in feet

Convert first. One foot is 0.3048 meters, so a 20 ft bar is 6.1 meters. For a 10 mm square, weight per meter is 0.785 kg, so the bar weighs 0.785 x 6.1 = 4.79 kg.

RealEdge MS Square Sizes and Weight Chart

SRMB RealEdge offers MS square in four sizes that suit grill, gate and fabrication work. The chart below shows theoretical weights for the standard 6 meter length, along with the approximate number of bars in one tonne.

MS Square Size (mm)Weight per Meter (kg)Weight per 6 m Bar (kg)Approx. Bars per Tonne
8 x 80.503.01332
10 x 100.794.71212
12 x 121.136.78147
16 x 162.0112.0683

These are theoretical figures. Actual weight can vary slightly, because rolled square bars have small rounded corners and permitted rolling tolerance.

Why Calculated Weight and Actual Weight Can Differ

A calculator gives you the ideal weight. What you receive depends on how well the bar was rolled. If a bar is rolled slightly under size, or if thickness varies along its length, the real weight falls below the calculated weight, and you pay for steel you do not get.

This is why consistent rolling matters. SRMB is a pioneer in 100 percent automated block mills with tungsten carbide rollers, which deliver perfect shape, uniform size, an equal standard length of 6 meters and consistent section weight. When section weight is consistent, the number you calculate matches the number you receive.

How RealEdge MS Square Is Made

Captive billet. RealEdge MS square is rolled from SRMB’s own captive billet, cast from superior quality ore sourced material and tested for carbon, sulphur and phosphorus. This keeps the chemistry consistent from batch to batch.

High speed, no twist block mill. MS Squares, along with MS Flats, Angles, Gate Channels and Z Angles, are made in a high speed, no twist block mill for precise dimensions and superior mechanical properties.

Walking type cooling bed. Hot bars cool evenly on an automated cooling bed without manual handling, so they stay straight and free from defects.

Quality control. Advanced European technology and NABL accredited labs support batch to batch consistency. RealEdge Square Bars (ISSQ) conform to IS 1732:1989, and the structural sections conform to IS 2062:2011.

Key Features of RealEdge MS Square

  • BIS certified and precise in quality
  • Superb finish with smooth edges
  • Fins free and defect free
  • Properly straightened
  • Uniform size along the full length
  • Greater malleability for decorative and better designs
  • Cost efficient to the grill fabricator

Step by Step: Estimating Your Order

  1. Choose the size based on your design, for example 12 mm for gate bars
  2. Note the bar length, usually 6 meters
  3. Look up the weight per meter in the chart above, or use the formula
  4. Multiply by length and quantity to get total weight
  5. Multiply by the rate per kg to estimate cost
  6. Add a small allowance for cutting waste, often 3 to 5 percent

Following these steps helps you order the right quantity the first time.

Common Uses of MS Square Bar

  • Gates: vertical bars and infill work
  • Window grills: bars for safety and design
  • Railings and fencing: posts and rails
  • General fabrication: frames, supports and small structures
  • Decorative work: twisted or scrolled bars for designer grills

Because it is made under the promise of “Steel for Grill,” the RealEdge range suits these applications especially well.

MS Square vs MS Flat vs Round Bar

Bar TypeCross SectionTypical Use
MS SquareEqual sidesVertical bars in gates and grills
MS FlatRectangularFrames, scrolls and bent designs
Round BarCircularRods, pins and reinforcement

For weight, the square bar formula uses side x side. For a flat bar, use width x thickness instead. For a round bar, use 0.00617 x diameter x diameter.

Frequently Asked Questions

How do you calculate the weight of an MS square bar?

Multiply 0.00785 by the side in mm twice, which gives the weight in kg per meter, then multiply by the length in meters.

What is the weight of a 12 mm MS square bar per meter?

A 12 mm MS square weighs about 1.13 kg per meter, or about 6.78 kg for a 6 meter bar.

What sizes of MS square does SRMB RealEdge offer?

SRMB RealEdge offers MS square in 8, 10, 12 and 16 mm.

What is the standard length of MS square bar?

RealEdge sections come in a standard length of 6 meters.

How many 12 mm square bars are in one tonne?

About 147 bars of 6 meters each, based on theoretical weight.

Is theoretical weight the same as actual weight?

Not exactly. Small corner radii and rolling tolerance can cause slight variation, so use theoretical weight for planning and confirm with your supplier.

What is the difference between MS square and MS flat?

MS square has equal sides and is used for vertical bars, while MS flat is rectangular and bends more easily into frames and scrolls.

Does RealEdge MS square follow any standard?

Yes. RealEdge Square Bars (ISSQ) conform to IS 1732:1989, and RealEdge sections also conform to IS 2062:2011.

Calculate Smart, Build Strong with SRMB RealEdge

Accurate weight calculation helps you plan cost, transport and quantity with confidence. But a calculation only holds up when the steel is made to a consistent standard.

SRMB RealEdge makes MS square from captive billets in an automated block mill, cooled on a walking type cooling bed and tested in NABL accredited labs, so the weight you plan for is the weight you receive. To order MS square in 8, 10, 12 or 16 mm, visit or contact SRMB RealEdge, an MS square bar supplier in Kolkata, today.

👤

Rajesh Kumar Sharma

Senior Design & Fabrication Consultant, SRMB RealEdge

Rajesh brings over 18 years of experience in structural steel design and fabrication consulting. He has worked with more than 500 fabricators across East India and authored over 40 technical guides on material selection, corrosion protection, and best practices for steel construction.

Order the Right Quantity the First Time

To order MS square in 8, 10, 12 or 16 mm, contact SRMB RealEdge today.

Related Articles

Chat Karo, Baat Karo, Mulakaat Karo — chat with us on WhatsApp